YAMAHA TF-RACK

General Specifications

Outline		TF-RACK
Mixing Capacity	Input Channels	40 (32 mono + 2 stereo + 2 return)
	Aux Buses	20 (8 mono + 6 stereo)
	Stereo Buses	1
	Sub Buses	1
Input channel functions		8 DCA Groups
I/O	Inputs	16 mic/line (XLR/TRS combo) + 1 stereo line (RCA pin)
	Outputs	16 (8 XLR + 8 TRS phone)
	Expansion slots	1 (for NY64-D)
On-board processors	DSP	8 Effects + 10 GEQ
General specifications		TF-RACK
Sampling frequency rate	Internal	48 kHz
Signal delay		Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader		Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Total harmonic distortion		Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω, INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Frequency response		+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range		110 dB typ., DA Converter, 108 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise level	Equivalent input noise	–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
	Residual output noise	–85 dBu, ST master off (Measured with an A-Weight filter)
Crosstalk		–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements		100–240 V 50/60 Hz
Power consumption		85 W
Dimensions	W	480 mm (18-7/8 in)
	H	132 mm (5-1/4 in)
	D	409 mm (16-1/8 in)
Net weight		9.2 kg (20.3lb)
Accessories		Quick Guide, Power Cord NUENDO LIVE (DAW Software), Rubber stoppers(4)
Options		Audio Interface Card (NY-64D), Foot Switch (FC5)
Others		Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

 

Recording/ Playback

PC/Mac (USB2.0)	Recording 34 tracks, Playback 34 tracks
USB Storage Device	Recording 2 tracks (USB hard drive/ SSD)*, Playback 2 tracks (USB hard drive/ SSD/ thumb drive)

*Please note - USB thumb drives are not supported by TF for recording purposes. Please refer to this link for compatible hard drives.

Analog input characteristics

Input Terminals	GAIN	Load  Impedance	For Use With  Nominal	Input Level			Connector	balanced /  Unbalanced
				Sensitivity*1	Nominal	Max. before clip
INPUT1-16	+66dB	7.5KΩ	50-600Ω Mics  or 600Ω Lines	-82dBu (61.6μV)	-62dBu (0.616mV)	-42dBu (6.16mV)	Combo Jack (XLR-3-31 type *2 or TRS phone *3)	Balanced
	-6dB			-10dBu (245mV)	+10dBu (2.45V)	+30dBu (24.5V)
ST IN	—	10kΩ	600Ω Lines	-30dBV (31.6μV)	-10dBV (316mV)	+10dBV (3.16V)	RCA Pin Jack	Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.) 
*2. 1: GND, 2: HOT, 3: COLD 
*3. Tip: HOT, Ring: COLD, Sleeve: GND 
*4. In these specifications, 0dBu = 0.775Vrms. 
*5. +48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch. 

Analog output characteristics

Output Terminals	Source  Impedance	For Use With  Nominal	Output Level		Connector	balanced /  Unbalanced
			Nominal	Max. before clip
OMNI OUT 1-8	75Ω	600Ω Lines	+4dBu (1.23 V)	+24dBu (12.3 V)	XLR-3-32 type *1	Balanced
OMNI OUT 9-16					TRS Phone Jack *6
PHONES *5	100Ω	40Ω Phones	3mW	75mW	Stereo Phone Jack (TRS) *2	Unbalanced

*1. 1: GND, 2: HOT, 3: COLD 
*2. Tip: LEFT, Ring: RIGHT, Sleeve: GND 
*3. In these specifications, 0dBu = 0.775Vrms. 
*4. All output DA converters are 24bit, 128times oversampling. 
*5. The position of the level control is lowered by 16dB from the maximum. 
*6. Tip: HOT, Ring: COLD, Sleeve: GND

Digital input/output specifications

Terminals	Format	Data length	Audio	Connector
USB (TO HOST)	USB	24bit	34ch input / 34ch output, PCM	USB (B type)
iPad	USB	—	Playback: MP3 or WAV file data / Record: WAV file data	USB (A type)

 

Control I/O specifications

Terminals	Format	Level	Connector
NETWORK	IEEE802.3	10BASE-T/100Base-TX	RJ-45
FOOT SW	—	—	TS Phone